Horizon Fitness T4 Manuel d'utilisateur télécharger pdf (Page 41)

INTRODUCTION

IMPORTANT

PRECAUTIONS

ASSEMBLY

BEFORE

YOU BEGIN

TREADMILL

OPERATION

CONDITIONING

GUIDELINES

TROUBLESHOOTING

& MAINTENANCE

LIMITED

WARRANTY

MAINTENANCE

Cleanliness of your treadmill and its operation environment will keep maintenance problems and service calls to a

minimum. For this reason, we recommend that the following preventive maintenance schedule be followed.

AFTER EACH USE (DAILY)

Clean and inspect, following these steps:

• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.

• Wipe down the running belt, deck, motor cover, and console casing with a damp cloth. Never use solvents, as they

can cause damage to the treadmill.

• Inspect the power cord. If the power cord is damaged, contact Horizon Fitness.

• Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or cut.

• Check the tension and alignment of the running belt. Make sure that the treadmill belt will not damage any other

components on the treadmill by being misaligned.

EVERY WEEK

Clean underneath the treadmill, following these steps:

• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.

• Move the treadmill to a remote location.

• Wipe or vacuum any dust particles or other objects that may have accumulated underneath the treadmill.

• Return the treadmill to its previous position.

EVERY MONTH - IMPORTANT!

• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.

• Inspect all assembly bolts of the machine for proper tightness.

• Turn off the treadmill and wait 60 seconds.

• Wait until ALL LED lights turn off.

• Remove screws holding motor cover to the frame. Remove the lower mast bolts in order to slide the motor cover

upwards. While sliding the motor cover up the masts, be careful not to scratch the paint. Prop up the motor cover

to continue.

• Clean the motor and lower board area to eliminate any lint or dust particles that may have accumulated. Failure to

do so may result in premature failure of key electrical components.

• Vacuum and wipe down the belt with a damp cloth. Vacuum any black/white particles that may accumulate around

the unit. These particles may accumulate from normal treadmill use.

EVERY 6 MONTHS OR 150 MILES

It is necessary to lubricate your treadmill running deck every six months

or 150 miles to maintain optimal performance of your treadmill. Once the

treadmill reaches 150 miles, the console will prompt you to lubricate the

treadmill. Only use lubricant provided by Horizon Fitness!

• TURN OFF THE TREADMILL with the on/off switch, then unplug the

power cord at the wall outlet.

• Loosen both the rear roller bolts. (For best results, place two removable

marks on both sides of the frame and note roller position). Once

the belt is loosened, take the bottle of lubricant and apply it to the

entire top surface of the running deck. Tighten both rear roller bolts

(matching up the marks for proper position) to original position. After

you have applied lubricant, plug in the power cord, insert the safety

key, start the treadmill and walk on the belt for two minutes to spread

the lubricant.

• Once lubrication is complete, reset the console by pressing and holding

‘STOP’ and Speed ‘+’ buttons for 5 seconds.

Please contact Horizon Fitness with questions about applying lubricant to your treadmill.

RUNNING BELT

RUNNING DECK

LUBRICATION

1 2 ... 36 37 38 39 40 41 42 43 44

Commentaires sur ces manuels

Pas de commentaire

Horizon Fitness T4 Manuel d'utilisateur Page 41

Commentaires sur ces manuels

Produits connexes et manuels pour Conditionnement physique, gymnastique et musculation Horizon Fitness T4